You are here

Home

KERG

Error message

  • The specified file temporary://fileJ7VhQI could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://filebENy8l could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://filen8sUrZ could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://filetbcKNC could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://fileLHHLag could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://filevGO6yT could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://fileFGJGYw could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://file0zy0oa could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://fileZkLjQN could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://filefdoFjr could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://filezYxbO4 could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
  • The specified file temporary://file3JOTjI could not be copied, because the destination directory is not properly configured. This may be caused by a problem with file or directory permissions. More information is available in the system log.
Subscribe to RSS - KERG

KRGG, KERG : Firmware upgrade

Trimble Alloy receiver firmware has been updated to version 6.40 for KRGG and KERG stations. The new sitelog is available on the page of each station.

KERG, KRGG : Network maintenance on Thursday February 27, 2025

Network maintenance is planned on the Kerguelen VSAT link (KERG and KRGG stations) on Thursday February 27, 2025 around 05:00 UTC+1. The estimated duration of the outage is 2 hours.

KERG : Antenna cable change

Following an incident, the KERG station antenna cable was replaced by 30m + 30m + 8m cables, on 02-23-2024. A new cable without connectors will be installed later.

ASCG, CIBG, JFNG, KERG, KRGG, RGDG : Firmware upgrade

Trimble Alloy receiver firmware has been updated to version 6.20 for ASCG, CIBG, JFNG, KERG, KRGG and RGDG stations. The new sitelog is available on the page of each station.

Trimble receivers : firmware upgrade

Trimble NetR9 receiver firmware has been updated to version 5.56 for GAMB, GRAS, PAPE, THTI stations. Trimble Alloy receiver firmware has been updated to version 6.16 for ASCG, CHPG, CIBG, CPVG, FTNA, JFNG, KERG, KRGG, MAYG, OWMG, RGDG, TLSE stations. The new sitelog is available on the page of each station.

KERG : Receiver change

KERG Trimble NetR9 receiver was replaced on 2023-01-17 by a Trimble Alloy (firmware version : 6.14). New sitelog is available on this page.

KERG : Station is back on line

Station was unavailable from 2020-10-26 09:30 UTC to 2020-10-28 09:15 UTC, after a power outage. The following session has been lost : 2020-10-26 09:30 UTC to 2020-10-28 09:15 UTC.

CHPG, CIBG, CPVG, FTNA, HAO2, JFNG, KERG, MAYG, OWMG, RGDG, SEYG : Firmware upgrade

The firmware of CHPG, CIBG, CPVG, FTNA, JFNG, KERG, MAYG, OWMG, SEYG (Trimble NetR9) and HAO2, RGDG (Trimble Alloy) receiver have been updated on 2020-05-25 in 5.45 version.

CIBG, FTNA, JFNG, KERG, MAYG : Firmware upgrade

The firmware of CIBG, FTNA, JFNG, KERG and MAYG Trimble NetR9 receiver have been updated on 2020-02-19 in 5.43 version.